Vintage Guitar and Bass forum

Replacement bridge for Epiphone 2006 Ripper reissue?

Replacement bridge for Epiphone 2006 Ripper reissue?
« on: July 15, 2007, 06:40:05 AM »
Hey everybody. I will be getting my Ripper out of layaway (finally) pretty soon.

I have heard good things about these basses, but the one complaint I hear repeatedly is that the bridges are very difficult to tinker with. Apparently each saddle has four adjustment screws or something?

Anyway, won't know until I look at it, but let's say I wanted to replace the bridge with something easier to mess with and real solid...maybe even brass for a touch of brightness and to match the brass nut...what kind of bridge would you recommend?

Has anyone here got one of these theyve modded or upgraded in this way?

Replacement bridge for Epiphone 2006 Ripper reissue?
« Reply #1 on: July 18, 2007, 01:29:59 PM »
I hope someone will shed some light on this.  This may help determine if I end up buying one or not.

Replacement bridge for Epiphone 2006 Ripper reissue?
« Reply #2 on: July 19, 2007, 12:01:46 PM »
Humbug! The Epi Ripper bridge is a state of the art bridge in ABM/Hipshot style. A screw for intonation, one allen screw for unlocking the saddle horizontally to move it around with the aforementioned intonation screw and two allen screws to raise or lower the saddle plus another single one that locks the saddle vertically. If you do want to replace it, both an ABM and a Hipshot will do, but they have the same - disturbingly high?  :roll:  - amount of allen screws. The Epi bridge is even a bit more user friendly than the Gibson ABM one as one of the allen locking screws is slanted for better access without having to remove the string from the saddle slot.

If that is all too complicated for you you should maybe start playing guitar or something.  :lol:

I have two Epi Rippers, the current new limited edition and the prototype for it. Both are fine basses that need no upgrading whatsoever - pups, hardware and electronics are fine. In fact I prefer theses basses to my original Gibson Rippers, Grabbers and G-3 as they sort of melt these three models and their sounds into one.

Uwe

Replacement bridge for Epiphone 2006 Ripper reissue?
« Reply #3 on: July 24, 2007, 04:01:34 AM »
^^^

Thanks for the reassurance. Again, I haven't even SEEN or played one of these yet, but I'm super-close to having one in my hands. One more payment in a couple of weeks...

So, my reservations about the bridge were just based on some Harmony Central reviews that seemed to indicate they were a real bugger to set up, etc.

It's great to hear they are good to go in stock form. Can't wait to get mine. Haven't owned a bass in about 8 years. It's been hard to do without.

I consider myself a bassist first, but all I've had to get me by as far as instruments the past several years are a junky acoustic guitar and a couple of ukuleles.

I'm glad I scored one of these before they stopped production. I used to have a '76 Ripper and it was probably my favorite instrument I ever owned.

Replacement bridge for Epiphone 2006 Ripper reissue?
« Reply #4 on: July 25, 2007, 03:52:51 AM »
UPDATE:

Paid off the Epi GRipp3r today. Should have it in a week!

Replacement bridge for Epiphone 2006 Ripper reissue?
« Reply #5 on: July 27, 2007, 09:27:04 PM »
I would give the new bridge a shot.  I never had a Ripper, so both the 3 point and the Hipshot are new to me.  I like them both.  I think those who are very used to the 3 point may think the new bridge is too complicated.  I like the fact that I can raise string height more with the Hipshot.  However, the 3 point is cool and easy too. I think the hardware on the '06 is just fine, and I am keeping mine "stock".  I may change tuners on the '97 issue cause they seem like aluminum and slip a bit easier than the new Gotohs.

 

Recent posts on vintage guitar and bass

1970 Rosetti Epiphone guitar catalogScan of 1970 Epiphone guitar catalogue produced by Rosetti for the UK market. Undated but most likely from mid-late 1970, this was the first UK catalogue to show the new range of Japanese (Matsumoku) Epiphone guitars. Interestingly, these pages show the Epiphone solid bodies with a single-sided Fender-style headstock layout - a feature quickly replaced with a typical two-sided Epiphone headstock almost immediately. Epiphone electric guitars: 9520, 9525; bass guitars: 9521, 9526; acoustic guitars: 6730, 6830, 6834
1971 A World of Guitars by Rosetti catalogueScan of 1971 Rosetti catalogue (UK) featuring guitars from from numerous manufacturers worldwide: guitars by Epiphone, Hagstrom, Levin, Hoyer, Egmond, Eros, Moridaira, Kiso-Suzuki, Schaller, and Tatra.
1971 Selmer guitar catalogueScan of 1971 Selmer guitar catalogue showing the range of electric and acoustic guitars distributed by the company: guitars by Gibson, Yamaha, Selmer, Hofner and Suzuki. 1960s Selmer had always placed Hofner at the front end of their catalogues, no doubt these were the better sellers - but into the 1970s Hofner were slipping somewhat and only appear at the tail end of this publication, pride of place going to Gibson, and to a lesser extent Yamaha. In fact this is the last Selmer catalogue to include the many Hofner hollow bodies (Committee, President, Senator etc) that had defined the companies output for so many years - to be replaced in the 1972 catalogue by generic solid body 'copies' of Gibson and Fender models. A number of new Gibson models are included for the first time: the SG-100 and SG-200 six string guitars and the SB-300 and SB-400 basses.
1968 Selmer guitar catalogueScan of 1968/1969 Selmer guitar catalogue (printed July 1968), showing the entire range of electric and acoustic guitars distributed by the company: guitars by Hofner, Gibson, Selmer and Giannini. Selmer were the exclusive United Kingdom distributors of Hofner and Gibson at the time, and this catalogue contains a total of 18 electric guitars, 7 bass guitars, 37 acoustics, and 2 Hawaiian guitars - all produced outside the UK and imported by Selmer, with UK prices included in guineas. This catalogue saw the (re-)introduction of the late sixties Gibson Les Paul Custom and Les Paul Standard (see page 69) and the short-lived Hofner Club 70. Other electric models include: HOFNER ELECTRICS: Committee, Verithin 66, Ambassador, President, Senator, Galaxie, HOFNER BASSES: Violin bass, Verithin bass, Senator bass, Professional bass GIBSON ELECTRICS: Barney Kessel, ES-330TD, ES-335TD, ES-345TD, ES-175D, ES-125CD, SG Standard, SG Junior, SG Special GIBSON BASSES: EB-0, EB-2, EB-3 - plus a LOT of acoustics branded Gibson, Hofner, Selmer and Giannini
1961 Hofner Colorama IHofner Colorama was the name UK distributor Selmer gave to a series of solid and semi-solid guitars built by Hofner for distribution in the UK. The construction and specifications of the guitars varied over the period of production, but by 1961 it was a totally solid, double cutaway instrument, with a set neck, translucent cherry finish, six-in-a-row headstock, and Hofner Diamond logo pickups. Available as a single or dual pickup guitar, this sngle pickup version would have been sold in mainland Europe as the Hofner 161.
1971 Commodore N25 (Matsumoku)Commodore was a brand applied to a series of guitars produced in Japan at the well-respected Matsumoku plant from the late 1960s to the mid 1970s - and sold primarily (perhaps exclusively?) in the United Kingdom. The models bearing the Commodore name were all guitars available from different distributors with different branding. Although there may have been some minor changes in appointments (specifically headstock branding) most had the same basic bodies, hardware and construction. Equivalent models to the Commodore N25 (and this is by no means an exhaustive list) include the Aria 5102T, Conrad 5102T(?), Electra 2221, Lyle 5102T, Ventura V-1001, Univox Coily - and most famously the Epiphone 5102T / Epiphone EA-250.
1960 Hofner Colorama IIThe Hofner Colorama was the name given by Selmer to a series of solid (and semi-solid) body Hofner guitars distributed in the United Kingdom between 1958 and 1965. The Colorama name actually applied to some quite different guitars over the period, but in 1960 it was a very light, semi-solid, set necked guitar with one (Colorama I) or two (Colorama II, as seen here) Toaster pickups. Although an entry-level guitar, it was very well-built, and a fine playing guitar; certainly a step up (at least in terms of craftsmanship) from many of the Colorama guitars that would follow, and a good deal of the guitars available in Britain circa 1960.
1971 Epiphone 1820 (ET-280) bassBy the end of the 1960s, a decision had been made to move Epiphone guitar production from the USA (at the Kalamazoo plant where Gibson guitars were made), to Matsumoto in Japan, creating a line of guitars and basses significantly less expensive than the USA-built models (actually less than half the price). The Matsumoku factory had been producing guitars for export for some time, but the 1820 bass (alongside a number of guitar models and the 5120 electric acoustic bass) were the first Epiphone models to be made there. These new Epiphones were based on existing Matsumoku guitars, sharing body shapes, and hardware, but the Epiphone line was somewhat upgraded, with inlaid logos and a 2x2 peghead configuration. Over the course of the 70s, the Japanese output improved dramatically, and in many ways these early 70s models are a low point for the brand. Having said this, there are a lot worse guitars out there, and as well as being historically important, the 1820 bass can certainly provide the goods when required.
1981 Gibson MarauderProduction of Bill Lawrence's Gibson Marauder began in 1974, with production peaking in 1978. But by 1980 the model was officially discontinued, though very small numbers slipped out as late as spring 1981. Over 7000 examples shipped between 1974 and 1979, and although no totals are available for 1980 and 1981, it is unlikely production reached three figures in either of these years. These final Marauders were all assembled at the Gibson Nashville plant, and had some nice features not available through the later years of production, such as a rosewood fretboard, and in this case, an opaque 'Devil Red' finish. It's a great looking and fine playing guitar!