Vintage Guitar and Bass forum

Cases for EB3 and EB3L (Slotted Headstock) - The Same?

Cases for EB3 and EB3L (Slotted Headstock) - The Same?
« on: January 05, 2010, 09:38:02 PM »
I just picked up a case on eBay for my EB3L slotted headstock that is 46" long, 13-1/2" lower bout, and 11-1/2" upper - There is also another case listed for an EB3 (slotted as well) with the same measurements... Are the cases the same for the EB3/EB0 and EB3L/EB0L? I know they are listed as 540 and 540L in the vintage catalog, but are they actually different or are they the same in reality? Can anyone confirm please?
 
Thank you.
« Last Edit: January 05, 2010, 09:58:18 PM by Groover »

EB3 and EB-3L case Sizes
« Reply #1 on: January 07, 2010, 08:56:36 PM »
To answer your question, NO the cases are not the same.  The EB-3L (as you know) is 4 inches longer in scale and requires a longer case.  Given that you have a slot head the tuners face back and not out the side of the headstock so the case for that is even more custom and will have a light gold lining and the case will have a narrow head stock area.  The EB-3L's after 1972 are solid head and have the tuners coming out of the side of the head stock and required a wider head stock area on the case.  They also have a deep purple lining.  I have both EB-3L configurations.  So you know, the cases are very hard to come by.  I had to find a new case for my solid head and it took forever.  In fact I currently have my solid head 1973 EB-3L on ebay right now.  I have migrated to 5 strings and decided to keep my slot head because I like the look and offer my solid head to a good home.

Hope this helps,

Bill

Cases for EB3 and EB3L (Slotted Headstock) - The Same?
« Reply #2 on: January 07, 2010, 09:12:31 PM »
Thanks for reply. I did see your bass on eBay, and it's a looker! I also own both versions (split and solid) in the EB3L versions, but when I bought my split headstock a year or so ago, it didn't have a case. Do you think there may have been a very short period where they (like maybe early '72) where they made the split head EBL cases with purhaps purple lining like the 72 and up have? (my 72 is also like yours, wider head bed to accomodate tuners, and purple lining)
 
This is the case I just picked-up.
 
GIBSON EB BASS CASE
 
I'll be recieving it tomorrow, so I'll know then for sure. Dimensions as far a lenght and body go are correct, forgot to ask head width when I spoke with seller. Either way, I think I got a deal on it. If anything, I'll use that one for my EB3L (solid head) since it's newer, and get rid of the older one.
 
Thanks again!

EB3 and EB-3L case Sizes
« Reply #3 on: January 08, 2010, 02:29:45 AM »
Your very welcome.   The case you purchased is for the solid head.  Gibson was very particular about which case the EB-3L's went in.  I can't tell you why.  You will find that your slot head bass will want to slop around in that case.  I have tried it with mine.  I would recommend that you get some foam and make filler for the head stock area.  I will take a picture of the case that was made for the slot head so you have it with the dimensions.  I am impressed that you found the solid head case.  They are very hard to find.

If you have any friends that are looking for a solid head EB-3L please let them know of my ebay posting.

Best Regards,

Bill

Cases for EB3 and EB3L (Slotted Headstock) - The Same?
« Reply #4 on: January 08, 2010, 04:00:44 PM »
Quote from: Byte.dr;12895
.........I will take a picture of the case that was made for the slot head so you have it with the dimensions. I am impressed that you found the solid head case. They are very hard to find....

That would be great Bill. I will do the same, so at least we can help other EBL owners in the future. It's very hard to find good information on these models it seems.
 
My case is on truck out for delivery. I'll try and get some pics over the weekend and post here as soon as I get a chance.
 
Unfortunately none of my friends are bass players, well I do have one, but I can't convince him that Vintage stuff is great - he buys new off the shelf - were the two extremes when it comes to that.
 
Thanks again!

Cases for EB3 and EB3L (Slotted Headstock) - The Same?
« Reply #5 on: January 08, 2010, 05:45:25 PM »
Just arrive and only have measurements so far (my bass is at a different location)
 
and so far, I'm thinking this is correct case for the split-headstock EBL (still puzzled on the color of lining as I thought it should be gold as well)
 
Measurements (give or take 1/4" or so) Measured from inside to inside of padding)
  • 46" long
  • 5-3/4" at widest point at headstock
  • 11-1/2" at widest point of upper bout
  • 13-1/2" at widest point of lower bout
Cant wait to fit my bass in it! The case is clean!

Cases for EB3 and EB3L (Slotted Headstock) - The Same?
« Reply #6 on: January 10, 2010, 08:16:05 AM »
Quote
Groover wrote:still puzzled on the color of lining as I thought it should be gold as well

Hi, I have a 1970 EB-3L and the case I have for that is purple lined with the Gibson logo on the outside which I belive is the correct case. I do have another case which I use for my 1971 EB-3 (also split headstock) which is yellow/gold lined without a Gibson logo on the outside. It's actually the long enough to fit my EB-3L but I suspect it's a case for one of the lawsuit copies as the neither bass sits quite right in it around the body area. The Gibson case fits both bases nicely but I should really get the slighlty shorter case for the 71 EB-3.
 
G
 
http://www.myspace.com/motherlodeonline

Cases for EB3 and EB3L (Slotted Headstock) - The Same?
« Reply #7 on: January 13, 2010, 03:04:20 PM »
Finally got some pics.... perfect fit!
 
Thanks again for replies!
« Last Edit: January 13, 2010, 03:08:11 PM by Groover »

Gibson EB-3L slot head case
« Reply #8 on: January 23, 2010, 10:44:57 PM »
Hi,

The case for the slot head EB-3L is on ebay right now item number:120511070979.  You will see the yellow/gold lining and the head stock is narrower for the banjo tuners.


Best Regards,

Bill

jules

  • *****
  • 3068
    • View Profile
Gibson EB3L case
« Reply #9 on: January 24, 2010, 04:58:01 PM »
That's in pretty sweet condition
 
GIBSON EB-3L CASE
 
 
Slotted headstock basses are very prone to breaking, so correct cases are essential.
 
Is anyone aware of an aftermarket replacement case that works with these?

 

Recent posts on vintage guitar and bass

1970 Rosetti Epiphone guitar catalogScan of 1970 Epiphone guitar catalogue produced by Rosetti for the UK market. Undated but most likely from mid-late 1970, this was the first UK catalogue to show the new range of Japanese (Matsumoku) Epiphone guitars. Interestingly, these pages show the Epiphone solid bodies with a single-sided Fender-style headstock layout - a feature quickly replaced with a typical two-sided Epiphone headstock almost immediately. Epiphone electric guitars: 9520, 9525; bass guitars: 9521, 9526; acoustic guitars: 6730, 6830, 6834
1971 A World of Guitars by Rosetti catalogueScan of 1971 Rosetti catalogue (UK) featuring guitars from from numerous manufacturers worldwide: guitars by Epiphone, Hagstrom, Levin, Hoyer, Egmond, Eros, Moridaira, Kiso-Suzuki, Schaller, and Tatra.
1971 Selmer guitar catalogueScan of 1971 Selmer guitar catalogue showing the range of electric and acoustic guitars distributed by the company: guitars by Gibson, Yamaha, Selmer, Hofner and Suzuki. 1960s Selmer had always placed Hofner at the front end of their catalogues, no doubt these were the better sellers - but into the 1970s Hofner were slipping somewhat and only appear at the tail end of this publication, pride of place going to Gibson, and to a lesser extent Yamaha. In fact this is the last Selmer catalogue to include the many Hofner hollow bodies (Committee, President, Senator etc) that had defined the companies output for so many years - to be replaced in the 1972 catalogue by generic solid body 'copies' of Gibson and Fender models. A number of new Gibson models are included for the first time: the SG-100 and SG-200 six string guitars and the SB-300 and SB-400 basses.
1968 Selmer guitar catalogueScan of 1968/1969 Selmer guitar catalogue (printed July 1968), showing the entire range of electric and acoustic guitars distributed by the company: guitars by Hofner, Gibson, Selmer and Giannini. Selmer were the exclusive United Kingdom distributors of Hofner and Gibson at the time, and this catalogue contains a total of 18 electric guitars, 7 bass guitars, 37 acoustics, and 2 Hawaiian guitars - all produced outside the UK and imported by Selmer, with UK prices included in guineas. This catalogue saw the (re-)introduction of the late sixties Gibson Les Paul Custom and Les Paul Standard (see page 69) and the short-lived Hofner Club 70. Other electric models include: HOFNER ELECTRICS: Committee, Verithin 66, Ambassador, President, Senator, Galaxie, HOFNER BASSES: Violin bass, Verithin bass, Senator bass, Professional bass GIBSON ELECTRICS: Barney Kessel, ES-330TD, ES-335TD, ES-345TD, ES-175D, ES-125CD, SG Standard, SG Junior, SG Special GIBSON BASSES: EB-0, EB-2, EB-3 - plus a LOT of acoustics branded Gibson, Hofner, Selmer and Giannini
1961 Hofner Colorama IHofner Colorama was the name UK distributor Selmer gave to a series of solid and semi-solid guitars built by Hofner for distribution in the UK. The construction and specifications of the guitars varied over the period of production, but by 1961 it was a totally solid, double cutaway instrument, with a set neck, translucent cherry finish, six-in-a-row headstock, and Hofner Diamond logo pickups. Available as a single or dual pickup guitar, this sngle pickup version would have been sold in mainland Europe as the Hofner 161.
1971 Commodore N25 (Matsumoku)Commodore was a brand applied to a series of guitars produced in Japan at the well-respected Matsumoku plant from the late 1960s to the mid 1970s - and sold primarily (perhaps exclusively?) in the United Kingdom. The models bearing the Commodore name were all guitars available from different distributors with different branding. Although there may have been some minor changes in appointments (specifically headstock branding) most had the same basic bodies, hardware and construction. Equivalent models to the Commodore N25 (and this is by no means an exhaustive list) include the Aria 5102T, Conrad 5102T(?), Electra 2221, Lyle 5102T, Ventura V-1001, Univox Coily - and most famously the Epiphone 5102T / Epiphone EA-250.
1960 Hofner Colorama IIThe Hofner Colorama was the name given by Selmer to a series of solid (and semi-solid) body Hofner guitars distributed in the United Kingdom between 1958 and 1965. The Colorama name actually applied to some quite different guitars over the period, but in 1960 it was a very light, semi-solid, set necked guitar with one (Colorama I) or two (Colorama II, as seen here) Toaster pickups. Although an entry-level guitar, it was very well-built, and a fine playing guitar; certainly a step up (at least in terms of craftsmanship) from many of the Colorama guitars that would follow, and a good deal of the guitars available in Britain circa 1960.
1971 Epiphone 1820 (ET-280) bassBy the end of the 1960s, a decision had been made to move Epiphone guitar production from the USA (at the Kalamazoo plant where Gibson guitars were made), to Matsumoto in Japan, creating a line of guitars and basses significantly less expensive than the USA-built models (actually less than half the price). The Matsumoku factory had been producing guitars for export for some time, but the 1820 bass (alongside a number of guitar models and the 5120 electric acoustic bass) were the first Epiphone models to be made there. These new Epiphones were based on existing Matsumoku guitars, sharing body shapes, and hardware, but the Epiphone line was somewhat upgraded, with inlaid logos and a 2x2 peghead configuration. Over the course of the 70s, the Japanese output improved dramatically, and in many ways these early 70s models are a low point for the brand. Having said this, there are a lot worse guitars out there, and as well as being historically important, the 1820 bass can certainly provide the goods when required.
1981 Gibson MarauderProduction of Bill Lawrence's Gibson Marauder began in 1974, with production peaking in 1978. But by 1980 the model was officially discontinued, though very small numbers slipped out as late as spring 1981. Over 7000 examples shipped between 1974 and 1979, and although no totals are available for 1980 and 1981, it is unlikely production reached three figures in either of these years. These final Marauders were all assembled at the Gibson Nashville plant, and had some nice features not available through the later years of production, such as a rosewood fretboard, and in this case, an opaque 'Devil Red' finish. It's a great looking and fine playing guitar!