Vintage Guitar and Bass forum

RD Project bass

RD Project bass
« on: September 09, 2008, 02:03:49 AM »
OK....here is the first post for my RD project Bass. I got a neck off ebay with no fretboard on it. NOS gibson (greatdealz, of course), and bought a curly maple plank that I made a body blank with. Redbird was kind enough to send me a tracing of his RD (Thanks again SO much!) and I traced and cut a pattern for the body. Taped it to the blank, and a few router passes later got this........


Next, I cut a neck mortise template from a ripper body I have laying around (yet another project) and test fitted the neck. I am happy to report it is straight and tight. I can hold up the whole bass by the neck. I was amazed it was so snug.
Then I put the RD Standard pickguard (again, thanks, greatdealz) on the body and traced it so I would know where the pickups and screws would need to be. Then came the routing of the pickups


I wasnt too happy with the odd flame of the maple being so diagonal, so I got some heavy flame maple veneer and put it on top, re-routed the pickup and neck cavities, and have this....


I was thinking of finishing in a transparent blue burst finish similar to redbirds blueshawk bass (except with black on the edges) What do others think? I would love to get opinions on how you think I should go woth the finish. Also, what about controls....should I do 2v 1t like a regular standard, or a 2v 2t like an artist? One more....should I flame maple the headstock? or leave it black?

RD Project bass
« Reply #1 on: September 09, 2008, 04:53:46 AM »



RD Project bass
« Reply #2 on: September 10, 2008, 04:25:04 PM »
Wow, that would look äwesöme!

RD Project bass
« Reply #3 on: September 10, 2008, 06:09:29 PM »
Thanks. I`m hoping it comes out well. I am not planning on doing the binding like the artist CMT, but may do the thicker black border like the CMT.

RD Project bass
« Reply #4 on: September 10, 2008, 09:24:49 PM »
I think the blueburst would look great on there. I like it when people do an unusual finish instead of following the traditional color scheme. I'd probably go for the flame maple cap on the headstock also. Your project looks great!

RD Project bass
« Reply #5 on: September 11, 2008, 07:37:10 AM »
Hey anyfour, your bass is going to look great! I really like the finish you're thinking of. As an option though have you thought about a transparent wine red instead of the blue? I used to have a Yamaha SG3000s guitar that was a wine red burst with black edges and that was a lovely finish too.

G

www.motherlodeonline.co.uk

jules

  • *****
  • 3068
    • View Profile
great work
« Reply #6 on: September 11, 2008, 03:48:25 PM »
Yeah, really good work. Very inspiring. I'm tempted to have a go myself (I have necks and a loaded scratchplate...

I like the idea of binding though - looks really nice on the blue bass

Well done... looking forward to seeing the finished article

RD Project bass
« Reply #7 on: September 11, 2008, 06:45:54 PM »
Thanks for all the kind words everyone.

I have thought about other colors than blue. None really look right. THe wine red might look nice, but I have never been a big fan of red. lol

I may try the binding, but I have never done that before, and dont know if I can do it properly. Thats my main concern where that is.

I have also thought about buying the last 6 loaded scratchplates on ebay and making several more, if anyone is interested. I was going to see how this one came out, first.

RD Project bass
« Reply #8 on: September 11, 2008, 08:03:52 PM »
Sweet lookin bass! Im in need of a neck pocket tracing. Any chance you can scan one for me. ? I love these one off. bass projects. It just shows what mother gibby could be doing. Thanx for the inspired posts.M

RD Project bass
« Reply #9 on: September 13, 2008, 12:31:57 PM »
Great job. Blue burst is very cool.

RD Project bass
« Reply #10 on: October 21, 2008, 02:39:34 AM »
Time for an update....
THings have been slow going lately, but I have made significant headway on the body. Below you can see I have the bridge post holes and pot holes cut. Below that is the body cavity. I rounded off the back edge and put the countour on the back to make it a bit more comfortable.



You`ll notice in the pic above that I made the cavity cover out of the body material. It was much easier than I anticipated. I simply used leftover wood from the blank, put the fence of my table saw at about 1/4" and made a few passes on the different outside edges and then trimmed it down with a jigsaw. I think it will look really nice once the stain is on there.

And Jules, you`ll be happy to know I decided to DO the binding. I am waiting on the router bit from Stew Mac to cut the channel, and then the body will be done. The neck is coming along nicely as well. I have it shaped and the fretboard is on. I still need to sand the radius into the fretboard and then cut holes for the dots and fret it. Also, I need to cut peghead holes. I`m still undecided on the flame maple headstock in the blue, or Gibson black. Opinions?

As one more side note, reading the post regarding re-issues.....if anyone would like a new RD standard, let me know in PM. I havent completely priced it out yet, but once I make templates from this body, it should go much quicker, and you can have any finish you like on it.

RD Project bass
« Reply #11 on: October 21, 2008, 12:24:42 PM »
Great job and still my favorite bass.

RD Project bass
« Reply #12 on: November 04, 2008, 01:16:49 PM »
Nice job!
Especially the wooden coverplate in the back, nice detail :p

Great choice on the blue-burst also.
I'd go for the white binding though, it just looks too good.

I'm looking forward to see the (semi-)finished pics
- \'82 Gibson Victory Standard
- \'72 & \'78 Fender MusicMaster Basses
- \'50s / \'60s Egmond Princess 2
- Fender BG-32
- ...
Proud endorser of Crime Industries: http://profile.myspace.com/index.cfm?fuseaction=user.viewProfile&friendID=63949227

RD Project bass
« Reply #13 on: November 04, 2008, 01:18:30 PM »
Oh right, forgot:

I'd go for the black headstock...
Just feels better ;-)
- \'82 Gibson Victory Standard
- \'72 & \'78 Fender MusicMaster Basses
- \'50s / \'60s Egmond Princess 2
- Fender BG-32
- ...
Proud endorser of Crime Industries: http://profile.myspace.com/index.cfm?fuseaction=user.viewProfile&friendID=63949227

RD Project bass
« Reply #14 on: November 04, 2008, 04:35:17 PM »
I have put white binding on it. .090.....thick stuff. Was quite a task for my first binding job. lol I am now calling the body done. Its on to the neck. I have it radiused, and will put the dots and frets on it this week, as well as cut the tuner post holes in the headstock. Then its glue it together and see if it works!

 

Recent posts on vintage guitar and bass

1970 Rosetti Epiphone guitar catalogScan of 1970 Epiphone guitar catalogue produced by Rosetti for the UK market. Undated but most likely from mid-late 1970, this was the first UK catalogue to show the new range of Japanese (Matsumoku) Epiphone guitars. Interestingly, these pages show the Epiphone solid bodies with a single-sided Fender-style headstock layout - a feature quickly replaced with a typical two-sided Epiphone headstock almost immediately. Epiphone electric guitars: 9520, 9525; bass guitars: 9521, 9526; acoustic guitars: 6730, 6830, 6834
1971 A World of Guitars by Rosetti catalogueScan of 1971 Rosetti catalogue (UK) featuring guitars from from numerous manufacturers worldwide: guitars by Epiphone, Hagstrom, Levin, Hoyer, Egmond, Eros, Moridaira, Kiso-Suzuki, Schaller, and Tatra.
1971 Selmer guitar catalogueScan of 1971 Selmer guitar catalogue showing the range of electric and acoustic guitars distributed by the company: guitars by Gibson, Yamaha, Selmer, Hofner and Suzuki. 1960s Selmer had always placed Hofner at the front end of their catalogues, no doubt these were the better sellers - but into the 1970s Hofner were slipping somewhat and only appear at the tail end of this publication, pride of place going to Gibson, and to a lesser extent Yamaha. In fact this is the last Selmer catalogue to include the many Hofner hollow bodies (Committee, President, Senator etc) that had defined the companies output for so many years - to be replaced in the 1972 catalogue by generic solid body 'copies' of Gibson and Fender models. A number of new Gibson models are included for the first time: the SG-100 and SG-200 six string guitars and the SB-300 and SB-400 basses.
1968 Selmer guitar catalogueScan of 1968/1969 Selmer guitar catalogue (printed July 1968), showing the entire range of electric and acoustic guitars distributed by the company: guitars by Hofner, Gibson, Selmer and Giannini. Selmer were the exclusive United Kingdom distributors of Hofner and Gibson at the time, and this catalogue contains a total of 18 electric guitars, 7 bass guitars, 37 acoustics, and 2 Hawaiian guitars - all produced outside the UK and imported by Selmer, with UK prices included in guineas. This catalogue saw the (re-)introduction of the late sixties Gibson Les Paul Custom and Les Paul Standard (see page 69) and the short-lived Hofner Club 70. Other electric models include: HOFNER ELECTRICS: Committee, Verithin 66, Ambassador, President, Senator, Galaxie, HOFNER BASSES: Violin bass, Verithin bass, Senator bass, Professional bass GIBSON ELECTRICS: Barney Kessel, ES-330TD, ES-335TD, ES-345TD, ES-175D, ES-125CD, SG Standard, SG Junior, SG Special GIBSON BASSES: EB-0, EB-2, EB-3 - plus a LOT of acoustics branded Gibson, Hofner, Selmer and Giannini
1961 Hofner Colorama IHofner Colorama was the name UK distributor Selmer gave to a series of solid and semi-solid guitars built by Hofner for distribution in the UK. The construction and specifications of the guitars varied over the period of production, but by 1961 it was a totally solid, double cutaway instrument, with a set neck, translucent cherry finish, six-in-a-row headstock, and Hofner Diamond logo pickups. Available as a single or dual pickup guitar, this sngle pickup version would have been sold in mainland Europe as the Hofner 161.
1971 Commodore N25 (Matsumoku)Commodore was a brand applied to a series of guitars produced in Japan at the well-respected Matsumoku plant from the late 1960s to the mid 1970s - and sold primarily (perhaps exclusively?) in the United Kingdom. The models bearing the Commodore name were all guitars available from different distributors with different branding. Although there may have been some minor changes in appointments (specifically headstock branding) most had the same basic bodies, hardware and construction. Equivalent models to the Commodore N25 (and this is by no means an exhaustive list) include the Aria 5102T, Conrad 5102T(?), Electra 2221, Lyle 5102T, Ventura V-1001, Univox Coily - and most famously the Epiphone 5102T / Epiphone EA-250.
1960 Hofner Colorama IIThe Hofner Colorama was the name given by Selmer to a series of solid (and semi-solid) body Hofner guitars distributed in the United Kingdom between 1958 and 1965. The Colorama name actually applied to some quite different guitars over the period, but in 1960 it was a very light, semi-solid, set necked guitar with one (Colorama I) or two (Colorama II, as seen here) Toaster pickups. Although an entry-level guitar, it was very well-built, and a fine playing guitar; certainly a step up (at least in terms of craftsmanship) from many of the Colorama guitars that would follow, and a good deal of the guitars available in Britain circa 1960.
1971 Epiphone 1820 (ET-280) bassBy the end of the 1960s, a decision had been made to move Epiphone guitar production from the USA (at the Kalamazoo plant where Gibson guitars were made), to Matsumoto in Japan, creating a line of guitars and basses significantly less expensive than the USA-built models (actually less than half the price). The Matsumoku factory had been producing guitars for export for some time, but the 1820 bass (alongside a number of guitar models and the 5120 electric acoustic bass) were the first Epiphone models to be made there. These new Epiphones were based on existing Matsumoku guitars, sharing body shapes, and hardware, but the Epiphone line was somewhat upgraded, with inlaid logos and a 2x2 peghead configuration. Over the course of the 70s, the Japanese output improved dramatically, and in many ways these early 70s models are a low point for the brand. Having said this, there are a lot worse guitars out there, and as well as being historically important, the 1820 bass can certainly provide the goods when required.
1981 Gibson MarauderProduction of Bill Lawrence's Gibson Marauder began in 1974, with production peaking in 1978. But by 1980 the model was officially discontinued, though very small numbers slipped out as late as spring 1981. Over 7000 examples shipped between 1974 and 1979, and although no totals are available for 1980 and 1981, it is unlikely production reached three figures in either of these years. These final Marauders were all assembled at the Gibson Nashville plant, and had some nice features not available through the later years of production, such as a rosewood fretboard, and in this case, an opaque 'Devil Red' finish. It's a great looking and fine playing guitar!